We will only service e-bikes with Bosch, Shimano, Fauza, TQ, Hyena, and Specialized electronics. Electronics include the battery, motor, controller, wiring, and any other parts related to the electrical component of an e-bike. We can work on the mechanical components of other e-bike brands but not the electronics. If you are leaving your e-bike for service and it does not have electronics from one of the aforementioned brands, we cannot keep the battery in the building due to insurance reasons and you must bring it home with you. If the battery cannot be removed from the bike, you must be present in the building while your bike is being worked on; it cannot be left for service.
Flat Repair
*Cost for rear wheel change only
Rear Hub Motor
For any rear hub motor-based ebike, usually any with a throttle.
$50
Mid Drive
For any mid drive motor-based ebike, usually any class 1 or 3 ebike.
$35
Ebike Tune Up Packages
Single Speed
$125
- Clean & Lubricate chain
- Clean bike
- Lubricate cables and housing
- Adjust brakes**
- Adjust chain tension
- Adjust Headset**
- Check Torque Specs
- Apply grease, Carbon Prep, and/or Titanium Prep as necessary
- True Wheels
- Firmware Update
- Check tire pressure
- Parts not included*
Standard Tune
$200
- Clean bike
- Clean and lubricate chain
- Lubricate cables and housing
- Lubricate pivots
- Torque fasteners
- Adjust brakes**
- Adjust derailleurs
- Adjust headset**
- True Wheels
- Check tire pressure
- Check Torque Specs
- Apply grease, Carbon Prep, and/or Titanium Prep as necessary
- Firmware updates
- Tubeless refresh
- Parts not included*
ProTune
$375
- Remove drivetrain Components
- Remove fork
- Thoroughly clean the bike
- Ultrasonically clean drivetrain***
- Install new cables and housing
- Lubricate cables and housing
- Lubricate pivots
- Reassemble the bike to the factory-recommended torque specs
- Apply grease, Carbon Prep, and/or Titanium Prep as necessary
- Adjust/Bleed brakes**
- Adjust derailleurs
- Overhaul hubs
- Overhaul headset
- Overhaul bottom bracket
- True wheels
- Tubeless refresh
- Drivetrain firmware updates
- Check tire pressure
- *Parts not included
*Certain components and safety items can be purchased through our online store.
**Prices may increase due to proprietary components and setup methods
***For ultrasonically drivetrain cleans, no electronic component is cleaned this way in order to prevent damage
Firmware Updating & Custom Tuning
Software Update
E-Bikes have brought a whole new service need to the world. Just like all of our other electronic devices, updates are required every so often. With this service, we are able to plug in to major drive systems including Shimano, Bosch, Fazua, Specialized and Electra Bikes.
$45
Custom Tuning
Most major manufacturers nowadays allow for much more customization within their systems than in years past. With this service we will consult with you to find out what you are looking for out of your bike, connect to you drive system and make necessary adjustments to each power level to best suit your needs.
$75 Starting
A La Carte Services
| Tubeless Refresh (Per Wheel) | $15 |
| Tubeless Set-up* (Per Wheel) | $40 |
| Tape Handlebar* | $20 |
| Spoke Replacement Front | $30 |
| Spoke Replacement Rear | $75 |
| Adjust Disc Brake Caliper* (Per Wheel) | $35 |
| Brake Bleed* (Per Wheel) | $65 |
| Derailleur Hanger Alignment | $25 |
| Adjust Mechanical Derailleur (Per Derailleur) | $25 |
| Adjust Electronic Derailleur (Per Derailleur) | $35 |
| Firmware Update Per Electronic Component | $20 |
| Firmware Update For Complete Electronic Set Up | $70 |
| Adjust Traditional Headset | $25 |
| Adjust Internally Routed Headset* | $75 |
| Install Traditional Headset | $50 |
| Install Internally Routed Headset* | $175 |
| Install Traditional Handlebar | $35 |
| Install Internally Routed Handlebar | $175 |
*Prices may increase due to proprietary components and setup methods
Cable Labor Table
These are the labor charges that we have established for installing new mechanical cables and housing under our à la carte service section. Within these labor charges, it does include the adjustment for either mechanical brakes or derailleurs. Unfortunately, with ebikes, a lot of the time companies run the cable and housing along the main harness and/or through the battery and motor mount areas. This results in more time being spent, and in the long run, the labor prices increase.
| External | Internal | Integrated | |
| 1 Cable + Housing | $45 | $75 | $100 |
| 2 Cable + Housing | $60 | $95 | $125 |
| 3 Cable + Housing | $75 | $115 | $150 |
| 4 Cable + Housing | $100 | $130 | $175 |
Dropper Post:
Replace/ install internal lockout/ dropper cable & housing: $95
*Cable and housing options are available for an additional fee starting at $10